Acoustic pipe listening
Sensitive sensor picks up leak noise through tiles and plaster
Farwaniya
Non-destructive leak detection in Ardhiya
In Ardhiya, leak detection starts by testing pipes under flat concrete slabs using differential pressure gauges. Escaping water reduces pipe pressure, and the difference between inlet and outlet pressures shows the gap location. In an industrial zone like Ardhiya, pipes carry heavy loads and leaks may come from corroded metal joints. We measure pressure precisely before breaking.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Villas and buildings in Ardhiya near the industrial zone sit on solid foundations but pipes under floors endure high pressure and thermal cycles. A leak from a copper joint may be very slow, taking weeks to raise water to the surface. We use a differential pressure gauge on the suspected pipe section and monitor pressure drop over time. If pressure falls steadily the leak exists, and where the drop is greatest shows the gap.
Ardhiya lies in Farwaniya near the industrial zone, a residential area with pipes laid under mechanical stress.
We test pipes at 10 bar pressure for 15 minutes because Ardhiya pipes feed from a nearby pump station under high pressure.
What this service covers
In-pipe camera inspection
Flexible camera checks for cracks and corrosion inside supply lines
Suspect line mapping
Tracing the hidden pipe route to narrow the search zone
Floor and wall survey
Systematic check of suspect surfaces without lifting a single tile
Roof tank check
Confirming whether moisture source is the tank or a supply pipe
Leak location report
Exact leak point confirmed before the repair team is engaged
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Non-destructive leak detection
Other services in Ardhiya
Camera leak detection
See the detailsLeak repair
See the detailsTank leak detection
See the detailsUnder-tile leak detection
See the detailsCommon questions
Questions about Non-destructive leak detection in Ardhiya
Need someone now? The emergency line is open any hour.
+965 9668 4964
How do you know the leak is under the floor and not inside the walls?
We test vertical and horizontal pipe sections separately. If pressure drops on the horizontal section under the floor the leak is there. If it drops on vertical pipes the leak is in walls or ceilings.
Can the pipe be fixed without opening the whole foundation?
Usually yes. We pinpoint the exact spot, typically opening only a small square around the gap. If the break is at a joint we cut and resolder it, or use a metal patch if it is along the pipe itself.
