Main line jetting
High-pressure water drives grease and sediment out of the main sewer run
Farwaniya
High-pressure jetting in Rai Industrial
High-pressure jetting in Rai Industrial Area handles large-diameter pipes serving factories and warehouses. We start with an industrial camera to inspect the full pipe length looking for metal scale, sand and industrial grease deposits. We send very high-pressure water jets to clean the pipe walls of all blockages. We re-inspect by camera to confirm the line is completely clear before the industrial operation resumes.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Factories and warehouses near The Avenues Mall in Rai Industrial drain water containing metal scale, fine particles and sometimes industrial oils. These materials accumulate quickly in the large pipes serving multiple facilities. Very high pressure removes thick deposit layers growing on pipe walls. We test large pipes carefully because excess pressure can damage older metal pipes more quickly.
Rai Industrial is an industrial zone in Farwaniya designated for factories, warehouses and major commercial centres.
We inspect large industrial pipes with high-resolution camera before and after jetting to formally document pipe condition.
What the jetting service covers
Kitchen line cleaning
Cuts through congealed oil layers that narrow the pipe wall over time
Manhole and gully jetting
Flushes accumulated sand and debris from inspection chambers and gullies
Pre-jetting camera check
Camera locates the blockage type and position before any jetting starts
Post-clear camera check
Camera confirms the pipe is fully clear; customer views the same screen
Commercial building networks
Adjusted pressure for longer pipe networks in complexes and restaurants
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for High-pressure jetting
Other services in Rai Industrial
Bathroom drain unblocking
See the detailsDrain snake unblocking
See the detailsKitchen drain unblocking
See the detailsMachine unblocking
See the detailsCommon questions
Questions about High-pressure jetting in Rai Industrial
Need someone now? The emergency line is open any hour.
+965 9668 4964
How many hours does clearing a large industrial line in Rai take?
It depends on line length and deposit thickness, usually between two and four hours. Very long lines serving multiple factories may take a full day. We estimate after the initial camera inspection and confirm before we start.
Can we jet the line while the factory is operating?
No, all drain points must be shut down during work so pressurized water does not back up through other points. We agree with factory management on suitable shutdown time. After jetting and final inspection are complete the line returns to service.
