Pipe repair
PPR, uPVC and corroded galvanised iron joints and runs
Jahra
Plumber (sabbak) in Jahra (Old)
Pipe and valve repair in Old Jahra near Jahra Fort requires special care because many houses still have very old pipes. We pinpoint the leak or fault precisely before starting. We replace only the faulty part and test it carefully. This approach maintains safety and proper pressure.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Old Jahra houses around the market have pipes hidden in thick stone and mud walls, and re-piping them damages heritage and structure. When a pipe weeps under the bathroom or kitchen we search precisely for the weak joint or clogged valve before opening the wall. We measure from the main shut-off to the leak point, opening at the closest spot. Often we find a copper joint crusted with sediment or an old valve needing gentle cleaning. We open it carefully, remove scale, re-seal with plumber's tape and silicone, then test flow slowly for two hours.
Old Jahra sits in Jahra governorate near the Red Fort, an established residential area with heritage houses some dating back a century.
We clean old brass valves with a soft brush then test at low pressure because heritage walls cannot tolerate repeated cutting.
What a sabbak handles
Mixers and valves
repair or replacement of leaking or stiff mixers and isolation valves
Water pressure
tracing low pressure to scale buildup, a blocked aerator or a pump fault
Fixture installation
fitting toilets, cisterns, basins and floor drains correctly and leak-free
Post-repair check
pressure test on the line after every repair before closing the wall
Fault diagnosis
locating the exact fault before any decision to break or repair
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Plumber (sabbak)
Other services in Jahra (Old)
Master plumber
See the details24-hour emergency plumber
See the detailsWater pump install and service
See the detailsWater tank cleaning
See the detailsCommon questions
Questions about Plumber (sabbak) in Jahra (Old)
Need someone now? The emergency line is open any hour.
+965 9668 4964
Is cleaning an old valve enough or must it be replaced?
Cleaning is usually enough if the valve still closes tight. We brush it gently, reassemble and wait two hours to confirm no weeping returns.
How do you avoid breaking old stone walls when searching for a leak?
We trace the water on the surface first, then measure from the main valve along the pipe itself. We open only at the safest nearest point, usually at a joint or bend.
