Crack mapping by camera
Internal camera maps every crack and its depth before work begins
Capital
Fibreglass tank repair in Shuwaikh Industrial
Fibreglass tank repair in Shuwaikh Industrial focuses on large tanks with solid bases on the ground beside production facilities. We inspect walls for cracks from machine vibration and heavy loading. We clean external rust and test the base joints under full pressure. We seal every crack with protective coating then fill slowly and watch.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Factories and warehouses in Shuwaikh Industrial rely on large fibreglass tanks with bases sitting directly on concrete, and these tanks move slightly as heavy machinery vibrates. Cracks start at the bottom corners where the wall meets the base and at side outlets bearing pipe weight. We climb and inspect the bottom seam line inside after drainage, because cracks under water cannot be seen.
Shuwaikh Industrial lies in Kuwait city and houses factories with large storage tanks, some subject to regular vibration.
After repair, we test the tank by raising internal pressure gradually because deep cracks burst under sudden overpressure.
What the repair covers
Surface preparation
Grinding the area around the crack ensures the resin bonds properly
Glass-mat laminate patch
Resin-saturated glass-mat layers fill the crack and restore structural stiffness
Delamination and wear repair
Delaminated sections are removed and rebuilt with matching laminate material
Drinking-water epoxy coat
Full interior coat with epoxy rated safe for potable water contact
Post-repair camera check
Camera confirms no remaining cracks or coating bubbles before the tank refills
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Fibreglass tank repair
Other services in Shuwaikh Industrial
Underground tank cleaning
See the detailsWater tank cleaning
See the detailsWater tank restoration
See the detailsEpoxy tank lining
See the detailsCommon questions
Questions about Fibreglass tank repair in Shuwaikh Industrial
Need someone now? The emergency line is open any hour.
+965 9668 4964
What is the difference between fixing a small and large crack in fibreglass?
Small cracks we inject with resin direct. Large cracks we open wider and add a reinforcing layer of glass cloth before resin. Large cracks need reinforcement because they can spread again.
Does the tank need to stop operating during repair?
Yes, the tank must stop completely because flowing water hides cracks and washes away resin before it sets. At factories we work nights or holiday days to cut production downtime.
