Acoustic surface scan
Tracing the leak sound through tile and screed layers
Farwaniya
Under-tile leak detection in Rabiya
Leak detection under tiles in Rabiya identifies leaking water with thermal equipment before any expensive repair call. We check damp floors and pinpoint the leak source by direct viewing and pressure testing. Precise location means no unnecessary tile breaking. You get a clear map of the leaking line.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Rabiya residential houses typically have living and bathroom floors over a network of cold water, hot water and waste lines. If water leaks from a cold line under tiles, you may see a damp patch slowly spreading on the floor, or smell must under carpets. We measure floor surface temperature with thermal imaging to see the abnormally cold zone pointing to the leak. Then we test the suspect line under steady pressure to confirm it is leaking. We mark the leak spot on the floor and give you a photo to keep when you request a repair.
Rabiya lies in Farwaniya governorate, a family residential area where original floors may contain older pipe runs.
We test each line at 8 bar for three minutes and wait before testing the next line to avoid mixing up leaks.
What this service covers
Pressure line test
Isolating the suspect line and measuring pressure drop to confirm fault location
In-line camera check
Filming inside the pipe from the nearest access point to view the crack
Leak point marking
Marking the exact spot on the tile surface to minimise breaking area
Concealed branch check
Checking pipe branches hidden inside the adjacent ceiling or wall
Link to leak repair
Handing the confirmed location directly to the repair team
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Under-tile leak detection
Other services in Rabiya
Non-destructive leak detection
See the detailsTank leak detection
See the detailsAcoustic leak listening
See the detailsCamera leak detection
See the detailsCommon questions
Questions about Under-tile leak detection in Rabiya
Need someone now? The emergency line is open any hour.
+965 9668 4964
Can you find the leak if the floor looks dry now?
If the floor is dry now but was wet before, we pressure-test lines to see which one leaks. Thermal imaging may see old moisture remnants below the surface. If no current leak shows, the line may be leaking intermittently.
How long does complete detection take from start to final report?
Visual inspection and thermal scan take about forty-five minutes. Pressure tests on all lines take thirty minutes more. We give you the report and map before leaving, roughly ninety minutes for the whole job.
