Acoustic surface scan
Tracing the leak sound through tile and screed layers
Ahmadi
Under-tile leak detection in Zour
Leak detection under tiles at Zour requires specialized sensors because the power station holds cold water lines, hot water lines and separate cooling pipes. We scan each line with thermal equipment then pressure-test the suspect pipe alone. We map the hole location and plot the repair route before management decides to open the zone. The full report arrives same day.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Zour power station is crammed with intersecting pipes below ground and thick concrete pads. When a leak happens near the pump room or cooling tank, water travels horizontally under the tile before showing on the surface far from its source. Thermal imaging finds the wet patch, but ultrasound traces the pipe run itself and pinpoints exactly where it broke. This saves the station hours of pump and cooling shutdown.
Zour lies in Ahmadi governorate and houses a major power generation station with intricate cooling pipes buried underground.
We measure surface temperature every 30 centimetres along the line because even a 2-degree difference reveals the leaking pipe route.
What this service covers
Pressure line test
Isolating the suspect line and measuring pressure drop to confirm fault location
In-line camera check
Filming inside the pipe from the nearest access point to view the crack
Leak point marking
Marking the exact spot on the tile surface to minimise breaking area
Concealed branch check
Checking pipe branches hidden inside the adjacent ceiling or wall
Link to leak repair
Handing the confirmed location directly to the repair team
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Under-tile leak detection
Other services in Zour
Non-destructive leak detection
See the detailsTank leak detection
See the detailsAcoustic leak listening
See the detailsCamera leak detection
See the detailsCommon questions
Questions about Under-tile leak detection in Zour
Need someone now? The emergency line is open any hour.
+965 9668 4964
How do you tell a cold water leak from a cooling line leak at the power station?
Cold water lines leave a very sharp cold spot on the surface, while cooling lines leave milder cold. We pressure-test each line separately to know which leaks, and this also shows which pipe needs fixing first.
Does the detection process shut down the station?
No, thermal and ultrasound scanning needs no pressure shutdown initially. We gather data on the surface first, and only before actual repair do we ask for the affected line to stop for just a few hours.
