Tank body inspection
Checking the outer shell and all joints for seepage or moisture
Capital
Heater leak detection in Dasma
A water heater leak in Dasma is usually spotted from damp marks on the wall or floor beneath the unit. We locate the exact leak point by checking the heater body, all fittings and the metal pipework. We test pressure in each section and pinpoint the leak source before any repair work starts.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
In Dasma apartments the heater often sits in a tight kitchen space or small bathroom, and the supply line may be fixed to an external wall. A slow leak from a fitting or the outlet line may not show until weeks later when water reaches the adjoining wall. We check each fitting with a hand-held pressure gauge and trace the leak direction from the moisture stains and discoloration on the brick.
Dasma is a residential district in the capital near Rawda and Qibla, where small flats with crowded electrical and water systems are common.
We measure cold and hot supply pressure separately because a hot-side leak may only show under the pressure created by heating.
What the detection covers
Acoustic leak tracing
Pinpointing concealed leaks by sound without opening the wall
Camera line check
Running a camera into supply or drain lines to trace the moisture source
Pipe connection check
Inspecting inlet, outlet and surrounding fittings for weeping joints
Fuel or power side
Checking the area around fuel or power entries for secondary moisture sources
Leak location report
Delivering a clear finding on where the leak is and what repair is needed
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Heater leak detection
Other services in Dasma
Electric heater repair
See the detailsGas heater service
See the detailsGeneral heater repair and service
See the detailsHeating element and thermostat
See the detailsCommon questions
Questions about Heater leak detection in Dasma
Need someone now? The emergency line is open any hour.
+965 9668 4964
How do I know the leak is from the heater body and not the inlet pipe?
We dry the inlet pipe with cloth first; if the damp spot on the wall stays dry, the leak is inside the heater body. We then measure water pressure to pinpoint the exact location within the tank.
If the outlet fitting leaks, can it be repaired without draining the tank?
Outlet fittings on pressure heaters need full drainage. We open the bottom drain valve, let the hot water cool, then unscrew the fitting with a wrench, clean the thread and install a new fitting with sealing compound.
