Element condition check
Resistance measured to confirm whether element is scaled, shorted or open
Capital
Heating element and thermostat in Abdullah Al-Salem
Replacing the element and thermostat in Abdullah Al-Salem starts with a full inspection of the unit, wiring and water temperature at the tap. We remove the metal cover, check the element for scale and cracks and test the thermostat reading at each setting. If water comes out warm or fails to heat then the element or thermostat needs immediate replacement. We fit the new element, calibrate the thermostat and run hot water for five minutes before handing over.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Most Abdullah Al-Salem houses were built in the seventies and eighties and their heaters run on steady pressure from a roof storage tank. This type of heater raises temperature fast but the elements suffer scale buildup from hard water. We dismantle each heater and inspect the base for heavy sediment blocking heat transfer, and remove the old thermostat which may give false readings due to moisture ingress.
Abdullah Al-Salem lies in Kuwait governorate, a long-established residential district with family houses and rooftop tanks feeding ground-level heaters.
We test hot water temperature at the tap with a digital gauge before leaving because older used heaters may warm slowly or unevenly.
What this service covers
Thermostat testing
Cutout points tested and temperature calibration verified before fitting new part
Tank interior inspection
Scale deposits inside the tank assessed as they reduce heating efficiency
Sacrificial anode check
Anode protects the tank from corrosion and is inspected at every service visit
Electrical connections
Wiring and terminals inspected for safety before the new element is energised
Post-replacement test
Heater run and water temperature confirmed at the tap before the visit ends
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Heating element and thermostat
Other services in Abdullah Al-Salem
Gas heater service
See the detailsGeneral heater repair and service
See the detailsHeater leak detection
See the detailsSolar heater repair
See the detailsCommon questions
Questions about Heating element and thermostat in Abdullah Al-Salem
Need someone now? The emergency line is open any hour.
+965 9668 4964
How do I know if the element is broken, not just the thermostat?
If water stays warm or cold despite running the heater for an hour, the element is likely broken. We switch on power and measure the element's electrical resistance with a tester, and if the reading is wrong the element must be replaced.
Should I flush the heater tank before fitting the new element?
Yes, if we see heavy sediment at the tank base we open the lower drain valve and empty water and deposits, then rinse the base with clean water. This improves the new element's performance and extends its life by removing mineral scale.
