Element condition check
Resistance measured to confirm whether element is scaled, shorted or open
Hawalli
Heating element and thermostat in Bidaa
Inspecting and replacing the heating element and thermostat in Bidaa heaters starts from knowing that most tanks here cycle intermittently due to heavy loads in modern apartment blocks. We open the tank and check element condition and lime buildup. We remove damaged parts, fit an element with appropriate power and a precise thermostat and test performance under full pressure.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Bidaa is a relatively modern residential area with tall apartment blocks and mid-range flats near the Salmiya seafront. Hot water tanks here are large to cover whole-building demand and usually sit in a plant room or on a common roof. Water in this area is relatively hard, causing lime deposits to build up quickly on the element surfaces, reducing heat transfer efficiency. Before replacement we check deposit thickness and decide whether cleaning is enough or full element replacement is needed.
Bidaa sits in Hawalli governorate near the Salmiya seafront, where salt air affects water quality.
We measure lime layer thickness on the element before replacement because hard water here deposits faster than other areas.
What this service covers
Thermostat testing
Cutout points tested and temperature calibration verified before fitting new part
Tank interior inspection
Scale deposits inside the tank assessed as they reduce heating efficiency
Sacrificial anode check
Anode protects the tank from corrosion and is inspected at every service visit
Electrical connections
Wiring and terminals inspected for safety before the new element is energised
Post-replacement test
Heater run and water temperature confirmed at the tap before the visit ends
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Heating element and thermostat
Other services in Bidaa
Gas heater service
See the detailsGeneral heater repair and service
See the detailsHeater leak detection
See the detailsSolar heater repair
See the detailsCommon questions
Questions about Heating element and thermostat in Bidaa
Need someone now? The emergency line is open any hour.
+965 9668 4964
Can cleaning lime deposits extend the current element's life?
Cleaning improves heat transfer for a time, but if deposits are more than a millimetre thick on the surface, the element loses efficiency quickly. In this case replacement is better than repeated cleaning.
Should water quality or filters be changed before fitting a new element?
We do not recommend filtering cold water before the tank as it reduces pressure. But if water is very hard, we suggest adding a small filter on the hot supply pipes only after the tank to reduce new deposits.
