Pipe repair
PPR, uPVC and corroded galvanised iron joints and runs
Farwaniya
Plumber (sabbak) in Rai Industrial
Precise plumbing repair in Rai Industrial focuses on heavy water lines serving shops and workshops. We check pumps, valves and large pipes from the entry point. We locate the fault by pressure and testing then replace the faulty part accurately.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Rai Industrial shops beside The Avenues Mall need steady water pressure all day for cleaning, washing and cooling. The main pipes here are wide-diameter and under high pressure, and even a small leak wastes hundreds of litres daily. We check the main valve chamber first to confirm the inlet stopcock, filter and water quality entering. If pressure is low we test the inlet pipe and pump if present before testing internal distribution lines.
Rai Industrial sits in Farwaniya governorate, a commercial-industrial district with shops depending on high and stable water pressure.
We test inlet pressure with a calibrated gauge and record the reading before and after pump activation.
What a sabbak handles
Mixers and valves
repair or replacement of leaking or stiff mixers and isolation valves
Water pressure
tracing low pressure to scale buildup, a blocked aerator or a pump fault
Fixture installation
fitting toilets, cisterns, basins and floor drains correctly and leak-free
Post-repair check
pressure test on the line after every repair before closing the wall
Fault diagnosis
locating the exact fault before any decision to break or repair
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Plumber (sabbak)
Other services in Rai Industrial
Master plumber
See the details24-hour emergency plumber
See the detailsWater pump install and service
See the detailsWater tank cleaning
See the detailsCommon questions
Questions about Plumber (sabbak) in Rai Industrial
Need someone now? The emergency line is open any hour.
+965 9668 4964
Why does water stop at the shop during peak hours?
Usually weak pressure in the inlet pipe or blockage in the main filter. We run the pump at full load while watching the pressure gauge and test each distribution valve. The cause might also be an invisible leak in the upper floor water line.
Does a weak water pump need replacement or can it be repaired?
First we check inlet and discharge pressure and clean the inlet strainer if blocked. If pressure remains weak we open the pump head and test the inlet and discharge valves. We replace worn seals and bearings before considering full pump replacement.
