Draining and deep clean
Sediment, algae and corrosion residue removed before any prep begins
Farwaniya
Epoxy tank lining in Abraq Khitan
Epoxy tank lining in Abraq Khitan protects family home tanks from leakage and rust in an active residential area. We drain the tank, completely scrape rust and deposits, apply rated epoxy in multiple coats, then test the seal before handover.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Abraq Khitan family homes rely on traditional steel tanks on roofs for daily water storage. Tanks face intense sun all day and sharp temperature drops at night, creating stress in steel and concrete. Rust starts as small spots on interior walls and develops into slow-leak holes. We pressure-test the tank to find every hole, then sand away all red rust and interior build-up until we reach clean bare metal. Three coats of food-grade epoxy provide a strong, flexible barrier that tolerates thermal expansion.
Abraq Khitan sits in Farwaniya governorate, a family residential district with steel tanks on roofs directly exposed to the sun.
We fill the tank very slowly then wait a full hour before declaring the job done to ensure no seepage.
What the lining covers
Surface preparation
Walls and floor abraded so the epoxy bonds without lifting or bubbling
Primer coat and finish coat
Two-coat system builds uniform thickness across all internal surfaces
Hairline crack filling
Fine cracks sealed with filler compound before coating, not over them
Post-cure camera check
Internal camera confirms full coverage and detects any early delamination
Safe return to service
Tank refilled only after the epoxy has fully cured, confirmed on site
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Epoxy tank lining
Other services in Abraq Khitan
Tank welding
See the detailsUnderground tank cleaning
See the detailsWater tank cleaning
See the detailsWater tank restoration
See the detailsCommon questions
Questions about Epoxy tank lining in Abraq Khitan
Need someone now? The emergency line is open any hour.
+965 9668 4964
What is the difference between epoxy protection and regular paint for tanks?
Regular paint only covers the surface and does not fill fine cracks, while epoxy penetrates pores and completely seals microscopic holes. Epoxy lasts much longer and does not peel or flake with heat and moisture.
Can tank coating work be done during hot summer?
Yes, but early morning work before peak heat is preferred. Intense heat speeds epoxy drying, which may make early coats too stiff before full spread.
