Crack welding
direct thermal weld along each fracture line in the tank wall
Ahmadi
Tank welding in Ali Sabah Al-Salem
Welded tank repair in Ali Sabah Al-Salem treats cracks and leaks in marine and coastal tanks exposed to salt and high humidity. We inspect the tank inside and out, pinpoint cracks and joint gaps with high precision. We apply salt and moisture resistant resin welding and pressure test under harsh conditions. The tank returns to service protected from long-term leaking.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Ali Sabah Al-Salem suburb sits near the coast with very high air humidity and salt that speeds rust on metals and cracking in plastic. Most houses have galvanised iron or fibreglass tanks on roofs and yards. Airborne salt settles on the tank surface, reacts with metals and weakens pipe joints. Plastic tanks crack faster than inland areas due to ultraviolet rays and salt together. We use epoxy resin with extra salt and moisture protection and apply an external protective coat after welding.
Ali Sabah Al-Salem is a coastal suburb in Ahmadi governorate where residential buildings sit near the sea with high humidity.
Welded tanks are tested with salt water mimicking the coastal environment because salt accelerates weak joint failure.
What the service covers
Joint repair
re-welding inlet and outlet fittings where the flange joint has failed
Fibreglass patching
resin-and-mat layer over the damaged zone before the final weld seal
Seal verification
internal camera after welding reveals any weak point before refilling
Hatch replacement
replacing the tank lid when the leak source is the cover seal
Post-work report
written record of weld locations and camera inspection result
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Tank welding
Other services in Ali Sabah Al-Salem
Underground tank cleaning
See the detailsWater tank cleaning
See the detailsWater tank restoration
See the detailsEpoxy tank lining
See the detailsCommon questions
Questions about Tank welding in Ali Sabah Al-Salem
Need someone now? The emergency line is open any hour.
+965 9668 4964
Can rusted plastic be fixed like rusted metal?
Plastic does not rust but cracks from ultraviolet rays and salt. We repair cracks with epoxy resin and an outer protective coat of thicker resin that prevents further cracking.
Does a coastal tank need regular maintenance after welding?
Yes, we recommend annual checks of the outer protective coat and look for salt buildup on the surface. Rinsing salt with fresh water keeps the resin from early weakening.
