Element condition check
Resistance measured to confirm whether element is scaled, shorted or open
Farwaniya
Heating element and thermostat in Firdous
Replacing the heating element and thermostat in Firdous starts by checking the space under the heater and measuring pipe distances. We drain the heater, remove the burnt element, install a new one with a calibrated thermostat and run a full cycle before handover.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Firdous houses in an area near the Sixth Ring Road have heaters mounted on bathroom or under-kitchen walls in tight spaces beside cold-water pipes. The heating elements in these conditions run at high voltage for extended periods and face corrosion from surrounding moisture. We check the holes holding pipes and the gap between heater and wall before extracting the element because tight space determines replacement size and mounting method.
Firdous lies in Farwaniya governorate near the Sixth Ring Road, a dense residential zone with closely-spaced family homes.
We measure the new element resistance before final installation because high bathroom humidity affects electrical joint quality.
What this service covers
Thermostat testing
Cutout points tested and temperature calibration verified before fitting new part
Tank interior inspection
Scale deposits inside the tank assessed as they reduce heating efficiency
Sacrificial anode check
Anode protects the tank from corrosion and is inspected at every service visit
Electrical connections
Wiring and terminals inspected for safety before the new element is energised
Post-replacement test
Heater run and water temperature confirmed at the tap before the visit ends
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Heating element and thermostat
Other services in Firdous
Gas heater service
See the detailsGeneral heater repair and service
See the detailsHeater leak detection
See the detailsSolar heater repair
See the detailsCommon questions
Questions about Heating element and thermostat in Firdous
Need someone now? The emergency line is open any hour.
+965 9668 4964
Can we fit a larger element in the old heater housing?
Not always, because diameter and length must match the space between heater walls. We measure the interior gap first and select a new element that fits exactly, and if the heater is too tight we may suggest replacing the whole unit.
How do we know if the thermostat is faulty?
Water either keeps heating past the target or starts heating too early, meaning the thermostat does not sense temperature correctly. We test it by measuring actual temperature at the sensor point and comparing it to the reading, then replace it if they do not match.
