Main pipe run
Running the supply line into the kitchen at the correct pipe diameter
Ahmadi
Restaurant gas lines in Zour
Installing a gas network in Zour restaurants near the power plant requires pipes running through high-temperature zones and strong mechanical forces. We use welded steel tubing, heat-resistant brackets and test both pressure and thermal isolation before handover.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Restaurant buildings in Zour sit near steam pipes and mechanical systems of the plant, which means the gas line cannot pass close to direct heat sources. We route pipe along a longer path away from any steam or thermal collector, with metal brackets at short intervals to reduce vibration from pumps and motors. We wrap pipe with thermal insulation at any point exceeding 40 degrees Celsius, and test under full pressure twice before handover.
Zour in Ahmadi governorate holds a major power generation plant and its associated industrial facilities, with canteens serving the workforce.
Because the plant generates continuous vibration, we check every metal bracket to ensure it does not loosen or shift before use.
What this service covers
Appliance branch points
Dedicated branch for each burner, oven, grill or fryer in the kitchen
Isolation valves
Valve at each appliance so one unit can be isolated without stopping the whole line
Concealed and surface routing
Pipes run inside the wall or surface-mounted to suit the building structure
Nitrogen pressure test
Completed network tested under dry nitrogen pressure before any appliance is connected
Existing network service
Inspecting or extending a working kitchen gas network with minimal downtime
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Restaurant gas lines
Other services in Zour
Gas leak detection
See the detailsKitchen gas lines
See the detailsCentral gas first-fix
See the detailsAblution basin
See the detailsCommon questions
Questions about Restaurant gas lines in Zour
Need someone now? The emergency line is open any hour.
+965 9668 4964
How do we protect gas pipes from heat off nearby steam lines?
We maintain at least 50 centimetres clear of any steam pipe, routing the gas line above or below with an air gap. Where distance is shorter we wrap the pipe with thick silicate insulation and verify it with a temperature gauge.
Does vibration from plant motors affect gas joint integrity?
Yes, continuous vibration loosens joints over time, so we install sturdy metal brackets every 1.5 metres and finish each joint with a tight pressure coupling. We test the network under full pressure again one day after installation to confirm stability.
