Dripping mixers
Source diagnosed; cartridge or seals replaced only as needed
Hawalli
Mixer and faucet repair in Nuqra
Mixer faucet repair in Nuqra addresses common failures in older homes with metal piping. We assess whether the leak is from the handle, the pipe connection or the internal valve. We test pressure and measure port sizes before selecting a repair part. We fit new washers or replace the cartridge as needed.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Nuqra homes near Salmiya have old-style brass mixers with thick metal handles and short welded connections. Rust and mineral salts accumulate inside over years because the local water is mineral-rich. When flow drops or cuts out, the valve port may be blocked by deposits. We carefully remove the mixer head using the right wrench to avoid damaging old brass. We clean the ports with a soft brush and light acid, then run water at high pressure to flush away buildup.
Nuqra in Hawalli sits near Salmiya and contains older homes where heavy brass mixers need periodic inspection.
Every repaired mixer is flushed with running water before final installation to ensure no metal particles remain in the ports.
What this service covers
Mineral scale buildup
Scale cleared from aerator, filter and internal mixer channels
Reduced flow
Fault located in mixer, supply valve or feed pipe
Incorrect temperature mix
Hot and cold channels checked and balance corrected
Faucet replacement
Old unit removed, new one fitted and pressure tested after
Isolation valves
Valve behind each fixture checked for full shut-off
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Mixer and faucet repair
Other services in Nuqra
Tank cleaning and waterproofing
See the detailsToilet and cistern repair
See the detailsValve repair
See the detailsWater leak detection
See the detailsCommon questions
Questions about Mixer and faucet repair in Nuqra
Need someone now? The emergency line is open any hour.
+965 9668 4964
Can an old mixer be cleaned of deposits without full disassembly?
Partially yes, we can inject a mild cleaning solution through control ports and leave it to work. But for complete results the head must be removed and internal parts cleaned by hand. This ensures all deposits are removed from the valve and diverter.
Is vinegar solution safe for cleaning a metal mixer faucet?
Yes, white vinegar is mild and safe on brass and steel if left no longer than one hour. But never use it on rubber washers or synthetic seals as it can make them brittle. We use purpose-made neutral solutions for mixers to prevent any damage.
