Crack mapping by camera
Internal camera maps every crack and its depth before work begins
Ahmadi
Fibreglass tank repair in Shuaiba Industrial
Fibreglass tank repair in Shuaiba Industrial starts with total water drawdown and internal inspection to spot every crack. We locate each defect and seepage point, then sand the surface and apply epoxy resin with a sealing coat to damaged areas. Water pressure testing confirms the tank holds full load again.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Fibreglass tanks in Shuaiba plants face high pressure from industrial water and salt exposure, and the smallest wall crack causes slow seepage between supply lines. During inspection we shine a bright lamp along the welded seam and corners where cracks first appear. If we find a crack longer than five centimetres we close it with a fibre patch before resin for extra strength. Water testing means slow fill and a two-hour stand to check for any new seepage.
Shuaiba Industrial lies in Ahmadi governorate and houses the KIPIC petrochemical complex where production relies on sealed fibreglass tanks.
Every tank is pressure-tested at full water load for two hours before restart because any seepage halts production.
What the repair covers
Surface preparation
Grinding the area around the crack ensures the resin bonds properly
Glass-mat laminate patch
Resin-saturated glass-mat layers fill the crack and restore structural stiffness
Delamination and wear repair
Delaminated sections are removed and rebuilt with matching laminate material
Drinking-water epoxy coat
Full interior coat with epoxy rated safe for potable water contact
Post-repair camera check
Camera confirms no remaining cracks or coating bubbles before the tank refills
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Fibreglass tank repair
Other services in Shuaiba Industrial
Underground tank cleaning
See the detailsWater tank cleaning
See the detailsWater tank restoration
See the detailsEpoxy tank lining
See the detailsCommon questions
Questions about Fibreglass tank repair in Shuaiba Industrial
Need someone now? The emergency line is open any hour.
+965 9668 4964
How long does it take to repair a small crack in the tank wall?
If the crack is under three centimetres, work takes two hours after drawdown. We clean, apply resin and let the seal cure four hours before testing.
Can the tank be repaired from the outside only?
No, the crack leaks from inside so the tank must be opened and inspected internally. Outer repair only seals the opening and does not stop the leak.
