Inspection and mapping
Internal camera maps every crack and spalled area before work starts
Ahmadi
Water tank restoration in Shuaiba Industrial
Water tank restoration in Shuaiba Industrial begins with a complete internal inspection of walls, floor and corners. We identify sediment, rust and fine cracks in concrete and existing lining. Deep cleaning removes all buildup, then we apply food-safe protective coating across every interior surface. The tank returns to service clean and protected.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Industrial Shuaiba has rooftop tanks on factory and workshop buildings, exposed to direct sun and high heat that accelerate internal corrosion. Water stagnating in summer heat leaves mineral deposits and chemical reactions that weaken the lining. We test water pH and salinity before choosing the coating type, because industrial tanks need stronger protection against fast rust formation.
Shuaiba Industrial sits in Ahmadi governorate, a zone of large factories and plants where water storage demand is high for daily production operations.
After cleaning, a camera probe is lowered to the tank floor to record every centimetre of interior surface before coating begins.
What restoration covers
Surface preparation
All scale, efflorescence and loose material removed before any filler is applied
Crack filling
Hydraulic mortar seals active and dry cracks in concrete walls and floor
Wall levelling
Repair render restores corroded or pitted wall surfaces to a uniform face
Protective coating
Drinking-water rated coating applied over fully cured and prepared surfaces only
Post-work check
Camera confirms coating integrity and joint sealing before the tank refills
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Water tank restoration
Other services in Shuaiba Industrial
Fibreglass tank repair
See the detailsRoof tank cleaning
See the detailsTank welding
See the detailsUnderground tank cleaning
See the detailsCommon questions
Questions about Water tank restoration in Shuaiba Industrial
Need someone now? The emergency line is open any hour.
+965 9668 4964
How often per year must an industrial water tank be cleaned?
In Shuaiba where heat and industrial dust are heavy, we advise inspection every six months and deep cleaning at least yearly. If the tank feeds a food production line, more frequent cleaning is required.
Will the protective coating withstand hot machine water and chemical additives?
The coating we apply resists temperatures to 60 degrees and is rated for lightly treated water. For lines with strong industrial additives, we test compatibility first and choose a stronger lining if needed.
