Crack welding
direct thermal weld along each fracture line in the tank wall
Mubarak Al-Kabeer
Tank welding in Sabah Al-Salem
Tank welding in Sabah Al-Salem addresses leaking joints and cracks in plastic and fibreglass tanks mounted on rooftops. We locate the leak by filling and pressure-testing the tank, then repair the damaged area with a weld that holds full pressure.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Most modern villas in Sabah Al-Salem have a fibreglass roof tank of 5 to 10 tonnes above the top storey, exposed to sun and heat cycling. Cracks usually appear around joints or at the tank base where the supply or overflow line connects. We access the roof, reach the tank and inspect every joint and bolt, then fully clean the damaged area before welding it.
Sabah Al-Salem sits in Mubarak Al-Kabeer governorate, a modern villa area with flat roofs that allow easy access to the elevated tank.
After welding, we fill the tank completely and wait one hour to check for any seepage from the repaired area.
What the service covers
Joint repair
re-welding inlet and outlet fittings where the flange joint has failed
Fibreglass patching
resin-and-mat layer over the damaged zone before the final weld seal
Seal verification
internal camera after welding reveals any weak point before refilling
Hatch replacement
replacing the tank lid when the leak source is the cover seal
Post-work report
written record of weld locations and camera inspection result
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Tank welding
Other services in Sabah Al-Salem
Underground tank cleaning
See the detailsWater tank cleaning
See the detailsWater tank restoration
See the detailsEpoxy tank lining
See the detailsCommon questions
Questions about Tank welding in Sabah Al-Salem
Need someone now? The emergency line is open any hour.
+965 9668 4964
Must the tank be completely drained before welding?
Yes, we drain it fully and allow it to dry for several hours, as water and moisture prevent the weld from bonding properly. After drying, we inspect the interior with a strong light to ensure it is clean.
Is fibreglass welding different from plastic tank welding?
Yes, fibreglass requires higher heat and a different technique because the fibre layers must stay bonded. We use a rod matched to each material and push the weld slowly to ensure it penetrates the full wall thickness.
