Inspection and mapping
Internal camera maps every crack and spalled area before work starts
Farwaniya
Water tank restoration in Ardhiya Industrial
Water tank restoration in Ardhiya Industrial begins with inspecting the steel structure, internal lining and connected pipework. We identify cracks, corrosion and leaks, then drain the tank, strip the old coating and apply a new protective lining before returning it to service.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Factories and processing plants in Ardhiya Industrial rely on large roof tanks and collection sumps at ground level, and these tanks corrode fast from industrial humidity and fumes. We check the tank floor first because sediment and debris build up there and accelerate rust, and we test metal flexibility at edges and corners where stress concentrates. Where we find small seam leaks we seal them with metal filler before lining, and where corrosion runs deep we recommend replacing weak wall sections.
Ardhiya Industrial sits in Farwaniya governorate, a district zoned for factories and warehouses that need tanks built to handle continuous heavy use.
Every restored tank is tested at full capacity with seams and floor inspected for a full hour before pump start because initial pressure reveals weak points.
What restoration covers
Surface preparation
All scale, efflorescence and loose material removed before any filler is applied
Crack filling
Hydraulic mortar seals active and dry cracks in concrete walls and floor
Wall levelling
Repair render restores corroded or pitted wall surfaces to a uniform face
Protective coating
Drinking-water rated coating applied over fully cured and prepared surfaces only
Post-work check
Camera confirms coating integrity and joint sealing before the tank refills
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Water tank restoration
Other services in Ardhiya Industrial
Fibreglass tank repair
See the detailsRoof tank cleaning
See the detailsTank welding
See the detailsUnderground tank cleaning
See the detailsCommon questions
Questions about Water tank restoration in Ardhiya Industrial
Need someone now? The emergency line is open any hour.
+965 9668 4964
How long does roof tank restoration take at a factory?
It depends on tank size and corrosion severity, but a medium tank takes two days to drain and clean and three days for lining and testing. We usually schedule work at night to minimize impact on production.
Does a new lining prevent rust from coming back?
High-grade epoxy or polyurethane lining isolates the metal from moisture for at least ten years. We advise inspecting every two years to catch any coating peeling at high-pressure areas.
