Acoustic detection
Pinpoints the leak behind tiles before any tile is touched
Farwaniya
Water pipe leaks in Rai Industrial
In Rai Industrial, workshops and warehouses have large-bore main supply pipes under high pressure, and a pinhole can suddenly blow into a gush. We use pressure sensors and thermal imaging to find the hole before it enlarges. We isolate the line from the control panel, cut out the damaged section and fit a reinforced steel section to matching engineering spec.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Rai Industrial warehouses built in the 1990s and 2000s have welded steel mains run at sharp angles near junctions with huge roof tanks. When a leak appears at a welds or near a shutoff valve, we stand at the pump and close the whole line. We listen for hissing or fine spray and scan the pipe with thermal imaging to see where cold is seeping. After precise pinpointing we cut the pipe on both sides, remove the bad section and weld a replacement of matching gauge and bore, then fill from the tank and pressure-test for ten minutes.
Rai Industrial sits in Farwaniya near The Avenues Mall and is zoned for factories, workshops and heavy storage plants.
The new section is tested at double normal operating pressure because industrial pipes bear intermittent heavy loads.
What this service covers
Camera line check
Films the pipe interior before and after repair work
PPR line repair
Damaged section replaced with heat-fused pressure-rated pipe
Galvanised pipe swap
Corroded galvanised iron replaced before internal rust causes burst
Pressure test
Confirms the repaired line holds before wall is closed up
Exposed roof pipes
Repairs leaks on roof-level supply pipes exposed to heat
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Water pipe leaks
Other services in Rai Industrial
Pipe unblocking
See the detailsPipe cleaning
See the detailsPipe insulation
See the detailsPlumbing installations
See the detailsCommon questions
Questions about Water pipe leaks in Rai Industrial
Need someone now? The emergency line is open any hour.
+965 9668 4964
How do we tell if a leak is at a weld joint or through the pipe wall itself?
With a sonic probe we hear interrupted spray at the joint, and thermal imaging shows concentrated cold. If the wall itself is leaking, spray will be spread out. We inspect the weld with magnification before cutting.
Must the workshop shut down while we repair the main water pipe?
Yes, we must close the main pump to isolate the line. We recommend scheduling repair during planned maintenance hours. Repair itself takes one to two hours depending on leak location and access.
