Electronic detection
sensors detect escaping gas through walls without any breaking
Hawalli
Gas leak detection in Salwa
Gas leak detection in Salwa starts by inspecting main supply lines from the house meter to every stove and water heater. We use an electronic detector to trace the characteristic odour and pinpoint the leak location precisely. We test every joint around valves and copper pipes running under floors and ceilings. We clean the area and close with a safety report.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Salwa houses near Salwa Co-op combine ground floors with cramped kitchens and upper storeys with tall water tanks on roofs. Gas lines run under kitchen and corridor tiles and climb inside walls to feed heaters on the roof. If the leak sits underground, tracing it means lifting some floor tiles and checking copper pipes for rust spots and fractures. If the leak is in the upper route, we follow the visible pipe run and inspect every joint around valves and fittings.
Salwa sits in Hawalli governorate, a densely built residential zone where central gas pipes deliver steady pressure to every flat and house.
We test every joint with soapy water to see leak bubbles because listening alone may miss tiny pinholes.
What this service covers
Pressure test
network segments isolated and pressure drop measured to find the faulty section
Joint inspection
every joint and valve checked with leak-detection fluid where leakage is suspected
Source isolation
gas isolated to the faulty section immediately to keep the building safe
Line repair
only the damaged section repaired or replaced, rest of network left intact
Final pressure check
full pressure test after repair confirms the entire network is tight
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Gas leak detection
Other services in Salwa
Kitchen gas lines
See the detailsRestaurant gas lines
See the detailsCentral gas first-fix
See the detailsPlumbing installations
See the detailsCommon questions
Questions about Gas leak detection in Salwa
Need someone now? The emergency line is open any hour.
+965 9668 4964
How do you locate a leak if it is buried under floor tiles?
The electronic detector homes in on the leaked gas odour and narrows down the zone. We lift tiles carefully along the route and look for rusted or cracked pipes. After repair we test with soap then reset the tiles.
Does a gas leak always mean a broken pipe?
No, the most common leak is at a joint around a valve or metal fitting due to vibration or corrosion. We disconnect the joint, clean the thread and fit a fresh washer and reliable tape.
