Crack welding
direct thermal weld along each fracture line in the tank wall
Ahmadi
Tank welding in Wafra
Tank welding at Wafra addresses cracks and failed joints in large irrigation and potable water tanks serving date palm and vegetable farms. We locate the leak by colored dye injection then drain the tank partly and remove any piping over the work area. We smooth the crack with flexible wire, fill it with strong resin and test it under full irrigation pressure before completion.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
Wafra lies near the Saudi border and is known for date palm and vegetable farming in wide fields under individual kiosks and centralized systems. Tanks here are massive galvanized steel or reinforced concrete set on deep foundations in sand and gravel. Saline water from deep wells causes rapid inner wall corrosion and concrete cracking around weak points. We test wall thickness with ultrasonic gauges and measure total salinity because excess salt causes new cracks quickly. Basic welding alone is not enough unless salt levels drop before the tank returns to use.
Wafra in Ahmadi governorate where groundwater for crop irrigation contains high concentrations of salt and minerals.
We test the weld by pumping actual irrigation water from the tank for two hours to monitor pressure and leaks under real use.
What the service covers
Joint repair
re-welding inlet and outlet fittings where the flange joint has failed
Fibreglass patching
resin-and-mat layer over the damaged zone before the final weld seal
Seal verification
internal camera after welding reveals any weak point before refilling
Hatch replacement
replacing the tank lid when the leak source is the cover seal
Post-work report
written record of weld locations and camera inspection result
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Tank welding
Other services in Wafra
Underground tank cleaning
See the detailsWater tank cleaning
See the detailsWater tank restoration
See the detailsEpoxy tank lining
See the detailsCommon questions
Questions about Tank welding in Wafra
Need someone now? The emergency line is open any hour.
+965 9668 4964
Does saline water cause permanent damage to tanks?
Yes, corrosion and cracking accelerate with salt. Welding fixes existing cracks but new ones appear if salinity stays high. Water analysis and salt reduction before welding extends tank life.
How long does a concrete tank need to dry after welding?
At least six hours before water is added again. Concrete needs longer than plastic because the resin must bond deeply into the pores.
