Crack welding
direct thermal weld along each fracture line in the tank wall
Hawalli
Tank welding in Ministries Area
Tank welding in Ministries Area handles cracks leaking from plastic and fibreglass tanks mounted on government building roofs. We locate the crack by sight inspection and partial filling, then measure tank wall thickness before starting work. We use heat welding for plastic or resin injection for fibreglass and let the repair cure fully before pressure testing.
- 24-hour emergency
- Camera first, every job
- Leak detection without breaking
- All six governorates
What sets this area apart
The administrative towers near Kuwait Government Ministries Complex hold large water tanks insulated with thick foam and shielded from sun by metal covers. These tanks bear steady pressure from fresh water and need regular inspection for fine cracks that appear at corners or inspection ports. When leaking shows in a drain valve below, the crack is often at the original weld joint or at the tank base where sediment settles. For repair we fully drain the tank and scrape any mineral deposits around the crack before welding.
Ministries Area sits in Hawalli governorate, a district housing government ministry headquarters and agencies in dense urban layout.
After welding the crack we fill the tank gradually while monitoring the spot for a full hour to ensure no water escapes.
What the service covers
Joint repair
re-welding inlet and outlet fittings where the flange joint has failed
Fibreglass patching
resin-and-mat layer over the damaged zone before the final weld seal
Seal verification
internal camera after welding reveals any weak point before refilling
Hatch replacement
replacing the tank lid when the leak source is the cover seal
Post-work report
written record of weld locations and camera inspection result
How we work
Our four steps, and you see every one
You call and describe it
Tell us what is happening and where, and the right equipment is loaded before we arrive.
The camera goes down
We film the line from inside and know the kind of blockage and its exact place. No guessing.
We clear it
High pressure water, a machine or a drain snake, whichever the line actually needs.
We film it again
The camera runs a second pass and you see the line clear with your own eyes before we leave.
Who we work for
Same method, same equipment. Only the size of the job changes.
Homes and apartments
- Drain and gully unclogging
- Cesspit suction
- Leak detection without breaking
- Tank cleaning and waterproofing
Offices
- Plumbing maintenance contracts
- Mixer and valve repair
- Low water pressure
- Clearing bathroom lines
Restaurants
- Grease traps
- Commercial kitchen lines
- Restaurant gas lines
- Scheduled clearing and cleaning
Complexes and buildings
- Sewer network maintenance
- Sewage and basement sump pumps
- Manhole and inspection chamber cleaning
- Operation and maintenance contracts
Why us
Why Al Amana
Amana means trust. Someone else's home is not ours to be careless in.
Filmed before and after
Do not take our word for it. Look at the line yourself.
Clearing before breaking
Breaking is the last resort, never the first step.
24-hour emergency
A blocked line does not wait for the morning.
All of Kuwait
Six governorates, 139 areas.
Maintenance contracts
For buildings and complexes, servicing before the problem starts.
We work on commercial sites too
Restaurants, offices and complexes, not only homes.
More areas for Tank welding
Other services in Ministries Area
Underground tank cleaning
See the detailsWater tank cleaning
See the detailsWater tank restoration
See the detailsEpoxy tank lining
See the detailsCommon questions
Questions about Tank welding in Ministries Area
Need someone now? The emergency line is open any hour.
+965 9668 4964
How do you ensure the weld will hold under water pressure?
We test the joint by filling the tank and directly observing the crack for an hour after welding. We also inspect repair quality from inside if the tank allows entry.
Can the tank be repaired without draining it entirely?
If the crack is at tank top we may lower water just below the crack level. But if it is at the base or sides, full drainage is needed to ensure the surface dries before welding.
